Smart Autodoor Firmware Changelog
Note: Firmware releases are now being made available to customers in waves, it may be a few days after the release date that the update becomes available for your device
v1.0.55 (Released 2026-03-30)
- Resolved issue where mains powered control panels may not automatically reconnect if the connection to the server was lost, requiring a manual power-cycle to reconnect.
- Control panels will now connect to the strongest available access point, not the first one they find when scanning.
- Mains powered control panels will now monitor the wifi signal strength, and if it is low, will periodically scan for a stronger access point, and switch if one is found, rather than remaining connected to the weaker signal (Not needed for battery control panels as they reconnect to the strongest access point every time they wake up).
v1.0.54 (Released 2025-12-01)
- If the unit is on mains power, the system will now report the power level only every 10 minutes to reduce the load on the Omlet infrastructure.
- Added additional logging for events related to reconnections to the Omlet infrastructure and detailed data during door movement
v1.0.53 (Released 2025-10-18)
- Resolved further issue with batteries draining quickly when unable to connect to the Omlet servers
v1.0.52 (Released 2025-10-16)
Note: This version was only released to a small number of users to aid with tracking down a connection issue
- Improved logging when connection to Omlet servers fails, to allow diagnosis of root cause
v1.0.51 (Released 2025-08-29)
- Resolved further issue with batteries draining quickly when wifi is enabled, but unavailable
- Resolved issue with control panels in Manual mode, using the Danish language presenting a blank home screen and becoming unresponsive
- Added new door faulted state when a door fault has occured and the position of the door is uncertain - this avoids reporting the door as closed when it may not be
- Resolved issues with logging that made diagnosing issues difficult for the IT team
- Added detection and notification of power faults due to low / poor quality batteries or power supply issues, with attempted auto-recovery
- Resolved issue with the control panel unexpectedly restarting after a brief wifi outage
v1.0.50 (Released 2025-07-17)
- Resolved issue with batteries draining quickly when wifi is enabled, but unavailable
v1.0.49 (Released 2025-06-06)
- Resolved issue with mains powered doors in time mode opening or closing at the wrong time following a power cut
- Resolved issue with app being out of sync with door status when using notification only mode, and the control panel failed to communicate with the server - it will now retry three times to send the status update
- Control panel will now remain in discovery mode if wifi connection succeeds, but it was unable to reach our server
v1.0.48 (Released 2025-05-14)
- Resolved issue with battery powered control panels closing slightly later than expected when coop light is set to turn on before close
- Corrected Dutch translations
- Removed a development menu item that would display in some circumstances
v1.0.47 (Released 2025-02-28)
- Resolved issue with control panels (particularly in Notification Only mode) not sleeping as long as they should, and thus consuming more battery than expected
v1.0.46 (Released 2025-02-14)
- Reverted change to light sensor reading calculation in 1.0.44
- Added light sensor calibration functionality
- Ensure control panel remains aware when door calibration is needed, and added feedback on display
v1.0.44 (Released 2025-01-22)
- Adjusted door blockage detection logic to overcome phantom blockages
- Adjusted light sensor reading calculation to ensure all light sensors reach 0
- Corrected further Swedish translations
v1.0.43 (Released 2024-10-29)
- Resolved issue with door reopening if manually closed before pre-set closing time
- Ensure crush message is visible on control panel if crush is present when open/close requested
- Ensure crush status clears immediately when resolved, rather than waiting for the next door open/close time
- Increased delay before screen turns off whilst navigating menu
- Resolved issue with incorrect numbering in menu after toggling light on or off
v1.0.42 (Released 2024-10-04)
- Fixed issue with control panel becoming unresponsive to button presses
v1.0.41 (Released 2024-10-02)*
- Fixed incorrect Swedish translation
- Fixed door blockage detection to resolve phantom blockages
- Fixed issue with being unable to control door after repeated start/stop requests
- Fixed issue with repeated coop light on/off events in app
- Fixed issue with coop light remaining on longer than intended
- Fixed issue with some doors opening/closing after firmware update
- Added switch to light mode after power cut when not using wifi (Read more…)
*Note: This firmware was only released to customers who had experienced a door blockage within the past 7 days, or reported a door blockage to our customer service team
v1.0.37 (Released 2024-09-10)
- Fixed issue with coop light being detected when not present
- Fixed issue with battery level reporting 0% if the battery level hadn’t been measured yet
- Fixed issue with control panel being reported as offline when it was still connected
- Fixed issue with phantom door blockage detection
- Removed door sensitivity setting – new process for door blockage detection no longer requires this setting
Note: If you have been experiencing phantom door blockages with previous firmware versions, please recalibrate your door after updating to this version
v1.0.36 (Released 2024-08-28)
- Battery life improvements:
- Resolved issue with control panel immediately re-waking if previously woken via button press in light mode
- Resolved issue with control panel not entering sleep if door moves while menu is active
- Resolved issue with control panel not entering sleep after door blockage detected
- Resolved issue with calibration never ending if door detected blockages at medium sensitivity
- Resolved issue with coop light max on time not being able to be set
- Resolved issue with control panel acting as if buttons are being held down when they are not
- Resolved issue with coop light state reporting on / off repeatedly when batteries are low
- Improved responsiveness when using buttons to wake from sleep in light mode
v1.0.35 (Released 2024-07-22)
- Resolved issue with Discovery Mode not exiting properly leading to battery drain due to sleep not starting
- Resolved issue with control panel not reconnecting to wifi in certain circumstances after power cuts
- Resolved issue with text wrapping on control panel display in certain languages
- Resolved issue with crush detection behaviour if crush detector is active when a futher attempt to close starts
- Resolved issue with coop light remaining on after door closed
v1.0.32 – (Released 2024-07-09)
- Resolved issue with time synchronisation not running on intended schedule
- Added forced time sync after completing firmware update
- Added the ability to trigger a time syncronisation remotely
v1.0.30 – (Released 2024-07-08)
- Added setting for door blockage sensitivity
- High – This is the standard setting for the new Smart Autodoor
- Medium – This is a reduced level of sensitivity, closer to the level of sensitivity on the classic Autodoor
- Updated calibration proceedure to automatically detect required sensitivity level for proper operation
- Resolved issue with status in app not updating if status changes (e.g. Door open / closed) while wifi is not connected – status will be updated the next time the control panel connects
- Resolved issue with stay alive functionality not working as desiged due to sleep countdown not being reset on receipt of stay alive message
- Resolved issue with overnight sleep starting when on battery and wifi connection failed after restart due to time not being set
- Resolved issue with control panel restarting if connection to server fails while door opening / closing – now waits until door has stopped moving
v1.0.26 – (Released 2024-06-28)
- Resolved issue with mains powered control panels reconnecting to the server every 3 minutes
v1.0.25 – (Released 2024-06-26)
- Resolved issue with coop light ignoring maximum on time setting and remaining on until manually turned off, or door closed (if night light is enabled) – draining the battery
v1.0.24 – (Released 2024-06-03)
- Resolved brownout issue due to behaviour of motor drives at power on
v1.0.23 – (Released 2024-05-24)
- Added the ability to turn off Wifi from the control panel menu, without requiring a factory reset. Retains Wifi settings to allow easy reconnection in the future
- Resolved issue with timezone change not applying until after reboot by rebooting if the timezone setting is changed
v1.0.20 – (Released 2024-04-03)
- Resolved issue with unlimited retries when crush detected while closing
- Resolved issue with setting control panel language from the Omlet App
- Resolved issue with Discovery Mode message not displaying after reboot
v1.0.19 – (Released 2024-03-26)
- Resolved issue with battery showing 100% when <= 0%
v1.0.18 – (Released 2024-03-26)
- Adjusted battery level calculation so that 0% is shown when the battery no longer provides enough power to move the door, rather than when it no longer provides enough power to run the control panel itself
- Adjusted threshold for accurate detection of coop light
v1.0.17 – (Released 2024-03-18)
- Control panel now retains IP address across sleep/wake cycles, allows for faster reconnection on waking
v1.0.16 – (Released 2024-03-16)
- Resolved issue with control panel going back to sleep before it has had time to connect to the server and send/receive messaged
- Removed reboot if wifi connection fails – control panel will now sleep and retry on the next wake cycle – constant reboot was causing battery drain
- Added additional device type information in the provisioning process, so the app can display the relevant device type to the user during setup
- Added coop light detection
- Resolved issue with control panel not performing door/light action with press & hold if control panel was asleep
- Resolved issue with Night Light setting causing the close time to be delayed when in time mode – light now switches on x minutes before the close time, rather than delaying the close time by x minutes
v1.0.15 – (Released 2024-02-27)
- Resolved issue with Discovery Mode not exiting properly, resulting in wifi remaining active and draining the battery
- Resolved issue with door calibration
- Resolved issue with screen remaining on and preventing the control panel from entering sleep after waking to move door
- Removed provisioning timeout when running on mains power
- Resolved issue with timezone setting not applying
- Resolved issue with overnight sleep not calculating correctly if starting sleep between midnight and the wake time (where sleep time is before midnight)
- Resolved issue with door behaviour differing between control panels
- Implemented a number of power management enhancements
v1.0.8 – (Released 2024-01-17)
- First production release
Note: Some development only releases are not listed here. The associated changes are listed with the versions where they were made publicly available